|
| |
Model 6510e/6530 Power Analyzers |
     |
| |
 |
The Magtrol 6510e Single-Phase and 6530 Three-Phase Power Analyzers are
easy-to-use instruments ideal for numerous power measurement
applications. From DC to 100 kHz AC, the 6510e and 6530 measure volts, amps, watts, volt-amps, frequency,
crest factor, Vpeak, Apeak and power factor in one convenient
display. They may be used either as stand-alone instruments
or in conjunction with any Magtrol Hysteresis, Eddy-Current
or Powder Brake Dynamometer;
any Magtrol Dynamometer
Controller and M-TEST Software for more demanding motor test applications. |
|
| |
| Features |
- Single/Three-Phase
Capabilities: Equipped to handle
single (6510e)
or three-phase (6530) power measurements
- Ranges: Up to
600 Vrms @ 20 A continuous duty
- Interfaces: RS-232 & IEEE-488 Interfaces
- Data Transfer Rates: Up to 100 per second
- Accuracy: Up
to 0.1%
- Vacuum Fluorescent Display: High-quality, easy-to-read, customizable readout displays
volts, amps, power and power factor
- Measurement: Continuous or cycle-by-cycle
- Bandwidth: DC
up to 100 kHz
- Input Power: Accepts 120/240 Vrms, 60/50 Hz power at 20 VA max
- Auto Ranging: Automatically scales instrument for most accurate
range
|
- Isolation: 1000
Vrms to earth, 750 line-to-line
- Average: Displays
running average of amps, volts and watts
- Peak Hold: Stores
the highest value read. Values can include amps, watts
and volts in any combination
- Analog Outputs: Plug-in module that provides 12 channels of analog
output corresponding to volts, amps and watts.
- External
Sensor Input
- Calibration Certificate: NIST Traceable
- Rack Mounting: 19" (482.6 mm) with handles
|
|
| |
| Applications |
- Motors and Drives
- Lighting Fixtures and Ballasts
- Office Equipment
- Household Appliances
- Power Tools
|
- HVAC Equipment
- Calibration of Test and Measuring Instruments
- Switching Power Supplies
- Power Inverters
- Transformers
|
|
| The 6510e's/6530's
data transfer rate makes them ideal for static and dynamic tests. |
| |
Back to top |
| |
|
| Technical Specifications |
| |
VOLTAGE INPUT |
CURRENT INPUT |
EXTERNAL
SENSOR INPUT |
POWER |
| Ranges |
30 V, 150 V, 300 V, 600 V |
1 A, 5 A, 10 A, 20 A |
50 mV, 250 mV, 500 mV, 1.0
V |
--- |
| Crest Factor |
2.7 @ full scale input |
1.7 @ full scale input |
2.4 @ full scale input |
--- |
| Impedance |
2 megohm |
12 milliohm |
17 kilohm |
--- |
| Display Range |
5 digits with 10 mV resolution |
5 digits with 1 mA resolution |
5 digits with 0.1 mV resolution |
6 digits with 1 mW resolution |
| ACCURACY |
| DC |
±(0.1%
Reading + 0.2% Range) |
0.4% of VA range |
| 5 Hz - 500 Hz |
±(0.1%
Reading + 0.1% Range) |
0.2% of VA range |
| 500 Hz - 10 kHz |
±((0.015
× F(kHz)% Reading) + 0.3% Range) |
0.6% of VA range |
| 10 kHz - 100 kHz |
0.6% + (0.03% × F(kHz)% of VA range) |
| >100 kHz |
N/A measurement band limited
to DC-100 kHz |
|
| |
| FREQUENCY |
| Source |
V1,A1, V2,A2, V3,A3,
LINE or EXT
(For Vx and Ax, source input must be >10% of range
setting) |
| Accuracy |
20 to 500 Hz 0.05% |
| EXT. Input |
BNC non-isolated, earth ground
referenced |
| Input Impedance |
100 kilohm |
| Voltage Level |
TTL / CMOS |
| Maximum Voltage |
50 V |
|
| |
| Back to top |
| |
|
| Analog Output Option |
| The Analog Output is a plug-in module designed specifically
for use with the 6510e Single-Phase Power Analyzer and 6530 Three-Phase Power Analyzer.
It provides up to 12 channels (3 for the 6510e,
12 for the 6530) of analog output corresponding to volts, amps
and watts. Each output is capable of, and calibrated to, ± 10
volts. With the analog output option, the user may apply a scale
factor to all outputs. Amps scaling is applied to all amp channels,
volts scaling is applied to all volt channels and watts scaling
is applied to all watt channels. |
| |
| Features |
- Simple Installation: Plug-in module automatically configures power analyzer
for operation
- Full Scale Output Range: ± 10V maximum output (user scalable)
- Up to 12 Channels: 6510e Single-Phase Power Analyzer (3 channels),
6530 Three-Phase Power Analyzer (12 channels)
|
- 14-Bit Resolution
- Frequent Output Updates: Updates every 5 milliseconds
- Output Short Protected
- Factory Calibrated: Calibration data/values stored on board (EEPROM)
- Industry Standard 25-Pin Connection
|
|
| |
| Applications |
| The Analog Output can be used along with a 6510e or 6530
Power Analyzer to output information to a strip recorder or
interface with a data acquisition system. The Analog Output
is also used as a safety feature to help trigger alarm events. |
| SPECIFICATIONS |
| Resolution |
14 bits |
Temperature
Coefficient |
4 ppm FSR/°C (typical),
20 ppm FSR/°C (maximum) |
| Output Range |
± 10 V maximum |
| Number of Channels |
12 |
| Basic Accuracy |
3 least significant bits |
Output Update Rate
(all channels) |
200 samples/second (5
ms) |
|
| Ordering
Information |
| 6510e |
Single-Phase Power Analyzer |
| 6510e-01 |
Single-Phase Power Analyzer
with Analog Output Option |
| 6530 |
Three-Phase Power Analyzer |
| 6530-01 |
Three-Phase Power Analyzer with
Analog Output Option |
|
| |
| Back to top |
| |
|
| External Shunts |
If currents continuously reach above 20 amps, an external sensor must be used. Magtrol offers three different types of external shunts for use with Magtrol Models 6510e or 6530 High-Speed Power Analyzers.
The HA Series shunt, designed for power cable hook-up utilizing 3/8-16 screws, has an insulating base and can be mounted on conductive surfaces. The LAB Series shunt also comes with an insulating base, along with thumb screws for the power leads and knurled nuts on the sensing terminals. The FL Series is a relatively small bus, bar-mounted shunt with large end blocks. The comparatively large end blocks and short spacing aid in cooling and allow the shunt to operate in more extreme environments. All shunts are calibrated on equipment with current certifications traceable to N.I.S.T. |
 |
| |
| Specifications |
| |
HA Series |
LAB Series |
FL Series |
| Rated Current |
50 A to 500 A |
750 A to 1000 A |
2000 A to 3000 A |
| Output |
50 mV |
| Bandwidth |
DC to 60 Hz |
| Accuracy |
± 0.25%
(± 0.1% accuracy with calibration certificate
is available for an additional cost) |
| Operating Temperature |
For optimum accuracy, temperature of shunt
should be 30 °C to 70 °C |
|
| Available Models |
| Type |
P/N |
Amps |
| HA |
004640 |
50 |
| HA |
004641 |
100 |
| HA |
004642 |
150 |
| HA |
004643 |
200 |
| HA |
004644 |
250 |
| HA |
004645 |
300 |
| HA |
004646 |
400 |
| HA |
004647 |
500 |
| LAB |
004648 |
750 |
| LAB |
004649 |
1000 |
| FL |
005214 |
2000 |
| FL |
005286 |
3000 |
|
| Sensor Substitution Wiring Connection |
 |
| NOTE: For the 6530 Three-Phase Analyzer, any (or all) of the Amps inputs may be replaced with a shunt for any of the wiring modes. |
|
| |
| Back to top |
| |
|
